Heating, Cooling, and Plumbing Services in Chesterfield, MO

Responded to a no hot water condition in a condominium utility closet and successfully installed a 40-gallon electric tall water heater with GE SmartWater™ branding featuring a 6-year limited warranty. Installation included two 3/4" ProPress ball valves for water supply connections, copper piping with appropriate fittings, and a metallic flexible corrugated connector at the top of the unit. All work was completed in accordance with permit #26PLU-09415, with proper plumbing identification sticker applied as required. The unit was installed in a compact utility closet space adjacent to the electrical panel, with all connections properly secured and tested for leaks. The water heater was energized, filled, and verified operational before departure, restoring hot water service to the property.

Completed comprehensive cooling season tune-up on 3-year-old residential air conditioning system. Performed full system inspection including control board evaluation, electrical connections check, and airflow assessment. Inspected air filter condition and verified proper system operation. Discussed preventive maintenance agreement options with homeowner for ongoing system care and extended equipment protection.

Completed comprehensive cooling system tune-up on 3-year-old outdoor AC unit. Performed standard maintenance protocol including inspection of condenser coils, which showed moderate accumulation of dirt and debris on exterior fins requiring cleaning attention. Unit operational and photographed for service records.

Responded to low refrigerant condition on KUBE-3A unit and added R22 refrigerant from truck stock to restore proper system charge. Weighed refrigerant tank before service showing 22 lbs, then topped off unit to manufacturer specifications to ensure optimal cooling performance.

Responded to no cooling complaint on upstairs unit. Upon inspection, diagnosed failed compressor motor on outdoor condensing unit. Removed and documented defective compressor assembly, which showed signs of operational wear and required replacement to restore cooling functionality.

Completed comprehensive air conditioning tune-up on single outdoor unit as part of scheduled maintenance program. Performed standard preventative maintenance procedures including inspection of condenser coils, which showed moderate dirt accumulation and environmental staining, and examination of refrigerant lines and connections. Replaced heavily soiled air filter that exhibited significant dust and debris buildup throughout the mesh structure, particularly in the upper sections, which was restricting proper airflow to the system.

Performed complimentary electrical inspection of exterior residential service equipment. Conducted visual assessment of main electrical meter enclosure, conduit routing, and mounting hardware on building exterior. Documented existing conditions through photographic records showing meter installation, protective enclosure with viewing window and safety labels, and metallic conduit run along exterior wall. Verified secure mounting of electrical components and noted current weathering patterns on outdoor-rated materials. All observations recorded for homeowner reference and future maintenance planning.

Completed comprehensive cooling tune-up maintenance on two residential air conditioning units (2018 and 2009 models). Performed standard U10 preventive maintenance protocol on both systems, including inspection of all major components, refrigerant level verification, electrical connection testing, condenser and evaporator coil assessment, and thermostat calibration. Inspected and documented air filtration systems for both units, noting pleated filter media condition on primary unit and honeycomb-cell filter configuration on secondary unit. Membership renewal was processed during the service visit to ensure continued maintenance coverage.

Completed comprehensive tune-up service on a 2-year-old residential air conditioning system. Upon arrival, found significant leaf debris and organic matter accumulated around the condenser unit base and along exterior panels. Cleared all debris from around unit perimeter and base to ensure proper airflow and prevent potential obstruction of heat exchange components. Performed standard preventive maintenance inspection of condenser unit, checking refrigerant levels, electrical connections, and overall system operation. Unit tested and operating within normal parameters upon completion.

Completed comprehensive cooling maintenance on three HVAC systems, performing standard tune-up procedures on all units. Replaced air filtration media with new pleated filters, inspected electrical components including capacitors and control boards, verified proper refrigerant line connections, and confirmed all systems are operating within normal parameters.

Completed preventative maintenance tune-up on two 2021 cooling units during morning service window. Performed comprehensive inspection of both systems including filter replacement on indoor air handler unit, exterior condenser coil cleaning to remove accumulated debris and dust buildup, and verification of proper mechanical operation. Both units tested and confirmed operating within normal parameters upon completion of service.

Replaced five aged toggle switches throughout the property, including a double-gang switch with discolored plastic housing and worn components observed on vintage wallpapered wall. All switches were tested for proper operation and functionality upon completion.

Responded to service call for 11-month-old upstairs attic unit experiencing noise when off and emitting musty odor. Upon inspection, found severely clogged 20x25x1 air filter with heavy dust and debris accumulation, restricting airflow and contributing to odor issue. Discovered significant condensation buildup on evaporator coil and interior ductwork, indicating inadequate airflow and potential drainage concerns. Replaced dirty air filter with new unit to restore proper airflow. Inspected condensate drain system and cleared minor blockage to ensure proper drainage. Cleaned evaporator coil surfaces to remove accumulated moisture and debris. Verified system operation after filter replacement, confirming reduced noise levels and improved air circulation. Advised homeowner on importance of regular filter changes every 30-60 days to prevent future airflow restrictions and maintain system efficiency. Unit operating normally at time of departure with proper airflow and no abnormal sounds dete

Completed preventive maintenance inspection on 6-year-old cooling unit located on basement pad. Inspected evaporator coil and found significant accumulation of dirt, dust, and debris throughout the fin surfaces, along with oxidation and discoloration compromising heat exchange efficiency. Cleaned condenser coil, checked refrigerant levels, tested electrical components, and verified system operation. Discussed service contract renewal options with customer for continued maintenance coverage.

Returned to property to re-route condensate drain line for new HVAC installation. Ran approximately 20 feet of 3/4" PVC piping behind furnace and over floor drain, utilizing two couplings and one 90-degree elbow fitting to properly configure drainage path. Removed and discarded previous condensate line configuration, securing new PVC run with appropriate clamps and ensuring proper pitch for drainage. System tested and confirmed operational with heat and cooling functions verified.

Replaced failed evaporator coil on second floor HVAC system. Removed existing coil showing signs of moisture accumulation and corrosion, installed new Lennox replacement unit, and integrated 2-inch coupling for proper fitment. System tested for heating and cooling operation, confirmed proper refrigerant charge and airflow. Disposed of old coil per standard procedures.

Completed comprehensive tune-up service on a 16-year-old residential air conditioning unit. Performed standard maintenance protocol including inspection of control board components, electrical connections, and wiring harnesses within the air handler cabinet. Installed new 20x25x6 MERV-rated media air filter to improve system air quality and efficiency.

Completed comprehensive cooling maintenance on a 9-year-old air conditioning system. Performed standard tune-up procedures including inspection of air return grille, verification of proper airflow through ventilation components, and detailed examination of control board wiring and electrical connections. All system components tested and found operating within normal parameters, with no issues identified during service.

Completed scheduled cooling season tune-up on residential A/C unit located on side of home. Performed comprehensive system diagnostics including electrical testing of blower motor assembly and compressor components using digital multimeter and clamp meter to verify proper amperage draw and voltage readings. All measurements fell within manufacturer specifications at 294.5V and 34.4A. Inspected blower motor housing, fan assembly, and associated wiring connections. System operating normally with no deficiencies noted.

Installed hardwired smoke alarms throughout residence, replacing previous plug-in units that were no longer functional. Work included mounting devices to ceiling locations in multiple rooms including master bedroom area, ensuring proper electrical connections and testing all units for operational functionality.