AC, Furnace & Plumbing Services in St. Charles, MO

Completed comprehensive cooling tune-up on outdoor AC unit, including inspection of condenser coil and fins, verification of refrigerant lines and insulation integrity, and air filter evaluation. Unit showed normal wear with minor dirt accumulation on condenser fins; all components operating within manufacturer specifications. System tested and confirmed ready for cooling season operation.

Responded to a no-cost callback for a recurring system issue. Upon arrival, performed diagnostic inspection of the HVAC unit's internal components, focusing on the condensate drainage system and refrigerant lines. Documented existing conditions including heavily corroded copper tubing and PVC trap configuration with photographic evidence for warranty documentation and future reference.

Completed comprehensive cooling tune-up on 21-year-old basement pad unit. Removed significant accumulation of organic debris (leaves, twigs, and decomposed plant material) that had compacted between unit housing and building structure, which was restricting airflow and potentially impacting system efficiency. Performed standard maintenance protocol including inspection of all components, cleaning of exterior surfaces, and verification of proper operation.

Installed a new 50-gallon gas tall water heater in a 1966-built home, replacing the existing unit. Connected gas supply line with shutoff valve, established proper venting, and verified all plumbing connections for safe operation. Unit backed by 10-year State manufacturer warranty with completion maintenance scheduled through 2026.

Completed cooling season tune-up on 7-year-old outdoor AC unit. Performed comprehensive system inspection including coil examination, which revealed significant dirt and debris accumulation on evaporator coil fins affecting airflow efficiency. Replaced 20x25x4 air filter with new pleated media filter to ensure proper system filtration and airflow. Inspected refrigerant lines and copper tubing for proper connections and insulation integrity. System operational upon completion of maintenance procedures.

Completed comprehensive whole-house electrical inspection of residential property. Thoroughly examined main electrical panel located in unfinished utility area, verifying proper circuit breaker operation, conductor connections, and panel labeling compliance. Inspected junction boxes, conduit installations, and wire routing throughout ceiling joists and structural framing. All electrical components, connections, and safety labeling were assessed for code compliance and proper installation standards. Documented findings with photographic evidence of electrical infrastructure conditions.

Completed comprehensive cooling tune-up on 12-year-old Ingersoll Rand 13 SEER air conditioning unit (Model 4TTB3030G1000AA) located in backyard. Performed standard maintenance protocol including inspection of condenser coils, electrical connections, refrigerant levels, and overall system operation to ensure optimal performance for the cooling season.

Installed new circuit breaker in existing electrical panel per approved estimate. Verified proper electrical connections, tested breaker operation, and confirmed all circuits functioning correctly upon completion.

# HVAC Cooling System Tune-Up Performed comprehensive preventive maintenance tune-up on a residential cooling system over 10 years old located in side yard. Conducted full system diagnostics and operational testing using digital multimeter to verify proper electrical readings and temperature measurements across all components. Inspected condensing unit, checked refrigerant pressures, cleaned condenser coils, and verified proper airflow. All system parameters found within normal operating specifications. Unit operating efficiently with no issues identified at time of service.

Completed scheduled cooling maintenance on 9-year-old Trane air conditioning system. Performed comprehensive AC tune-up including visual inspection of electrical components, capacitor assessment, and system operational verification. Inspected dual-run capacitor showing signs of age with surface corrosion and discoloration; capacitor tested within acceptable parameters and remains functional. Checked all electrical connections, contactor operation, and wiring integrity. System operating properly at time of service completion.

Completed preventive maintenance tune-up on a 10-year-old Goodman air conditioning system. Inspected outdoor condensing unit, verified proper airflow through grille assembly, and examined internal control panel wiring connections and circuit board components. All electrical connections, relay operation, and safety labels were checked and found to be in satisfactory working condition.

Completed annual cooling maintenance tune-up on HVAC system. Performed comprehensive inspection of blower motor assembly, verified proper operation and electrical connections, and replaced dirty air filter with visible dust accumulation. System tested and confirmed operating within normal parameters.

Responded to no-heat call for 10+ year old furnace located in basement. Upon arrival, discovered intake and exhaust vents obstructed by significant accumulation of dried vegetation, twigs, and organic debris. Cleared all blockages from both vent terminations at exterior wall, removing multiple buckets of material that had restricted airflow to the combustion system. Verified proper ventilation clearances restored, tested unit operation, and confirmed furnace returned to normal heating function.

Completed cooling tune-up on 5-year-old outdoor AC unit. Performed standard maintenance protocol including filter inspection, refrigerant line connections check, and system component evaluation. Filter showed moderate dust accumulation consistent with normal operation and was documented for future reference.

# HVAC Service Report - No Cooling Issue Responded to service call for air conditioning system not providing adequate cooling. Unit is a 16-year-old outdoor condenser that has reached the latter stage of its expected service life. Upon arrival, performed comprehensive system diagnostic to identify root cause of cooling failure. Conducted visual inspection of outdoor condenser unit, noting overall age-related wear consistent with 16 years of operation. Removed access panels to examine internal components, wiring connections, and electrical systems. Inspected control board and electrical connections within the unit, documenting the condition of multi-colored wiring harnesses including power supply lines, control wiring, and safety circuits. Verified integrity of wire connections and splice points, checking for loose connections, corrosion, or heat damage that could affect system performance. Examined condensate drainage system including PVC piping for proper flow and potential blocka

Removed evaporator coil from HVAC unit for thorough external cleaning due to significant dirt and debris accumulation affecting approximately two-thirds of the coil surface. The coil exhibited heavy blackened discoloration and grime buildup that was restricting proper airflow and heat exchange efficiency. After cleaning, reinstalled the evaporator coil and restored unit to proper operating condition.

Replaced failed blower motor on HVAC system using warranty-approved part that was delivered to the shop. Installed new motor, tested system operation to verify proper airflow, and disposed of defective component per standard procedures. Inspected air filter and outdoor condenser unit during service call, noting accumulated debris on condenser screen that may require future maintenance attention.

Removed existing PVC drain lines and water supply lines from original kitchen configuration. Re-routed 2-inch PVC drain piping and 1/2-inch water supply lines through basement ceiling joists to new island location, securing all lines per code requirements. Installed new loop vent system within the island hip wall to provide proper drainage venting for the relocated fixtures. Completed rough-in plumbing for kitchen sink drain and supply connections, dishwasher drain and supply hook-ups, and refrigerator water supply line at new designated locations. All piping installations positioned and ready for finish connections once cabinetry and appliances are set in place.

Performed comprehensive cooling season tune-up on a one-year-old residential air conditioning system. Conducted full system inspection including outdoor condenser unit and indoor air handler components, verified proper blower motor operation, inspected electrical connections and wiring harnesses, checked capacitor function, and cleaned condenser coil. All components found operating within normal parameters with system performing efficiently for continued cooling season operation.

Responded to no cooling call on 16-year-old residential air conditioning system. Upon arrival, confirmed blower motor operating but unit delivering warm air and running continuously without reaching setpoint. Performed diagnostic evaluation of outdoor condensing unit and indoor air handler components. Inspected refrigerant lines, electrical connections, and compressor operation. Documented equipment condition with photographs showing outdoor condenser unit installation and associated piping configuration. Identified system malfunction and provided customer with repair recommendations to restore cooling capacity.